Version bump to 8.22, update readme

CMakeLists.txt

@@ -40,7 +40,6 @@ include_directories(${PROJECT_NAME}
 )
 
 set(SRCFILES
-        Pins.h
         Config.h
         CharBuffer.cpp
         Network.cpp

Config.h

@@ -1,6 +1,6 @@
 #pragma once
 
-#define NUKI_HUB_VERSION "8.22-pre-1"
+#define NUKI_HUB_VERSION "8.22"
 
 #define MQTT_QOS_LEVEL 1
 #define MQTT_CLEAN_SESSIONS false

Gpio.cpp

@@ -1,7 +1,6 @@
 #include <esp32-hal.h>
 #include "Gpio.h"
 #include "Arduino.h"
-#include "Pins.h"
 #include "Logger.h"
 #include "PreferencesKeys.h"
 #include "RestartReason.h"

Network.cpp

@@ -19,6 +19,12 @@ Network::Network(Preferences *preferences, const String& maintenancePathPrefix,
   _buffer(buffer),
   _bufferSize(bufferSize)
 {
+    // Remove obsolete W5500 hardware detection configuration
+    if(_preferences->getInt(preference_network_hardware_gpio) != 0)
+    {
+        _preferences->remove(preference_network_hardware_gpio);
+    }
+
     _inst = this;
     _hostname = _preferences->getString(preference_hostname);
 
@@ -719,7 +725,7 @@ void Network::publishHASSConfig(char* deviceType, const char* baseTopic, char* n
                          "reset",
                          uidString,
                          "_reset",
-                         "Reset",
+                         "Restart NUKI Hub",
                          name,
                          baseTopic,
                          mqtt_topic_reset,

Pins.h

@@ -1,5 +0,0 @@
-#pragma once
-
-#define TRIGGER_LOCK_PIN 32
-#define TRIGGER_UNLOCK_PIN 33
-#define TRIGGER_UNLATCH_PIN 27

PreferencesKeys.h

@@ -25,6 +25,7 @@
 #define preference_ip_gateway "ipgtw"
 #define preference_ip_dns_server "dnssrv"
 #define preference_network_hardware "nwhw"
+#define preference_network_hardware_gpio "nwhwdt" // obsolete
 #define preference_rssi_publish_interval "rssipb"
 #define preference_hostname "hostname"
 #define preference_network_timeout "nettmout"
@@ -42,7 +43,7 @@
 #define preference_cred_user "crdusr"
 #define preference_cred_password "crdpass"
 #define preference_publish_authdata "pubauth"
-#define preference_gpio_locking_enabled "gpiolck"
+#define preference_gpio_locking_enabled "gpiolck" // obsolete
 #define preference_gpio_configuration "gpiocfg"
 #define preference_publish_debug_info "pubdbg"
 #define preference_presence_detection_timeout "prdtimeout"

README.md

@@ -23,6 +23,9 @@ As an alternative to Wifi, the following ESP32 modules with wired ethernet are s
 [M5Stack PoESP32 Unit](https://docs.m5stack.com/en/unit/poesp32)<br>
 [LilyGO-T-ETH-POE](https://github.com/Xinyuan-LilyGO/LilyGO-T-ETH-POE)<br>
 
+<br>
+<b>Note for users upgrading from 8.21 or lower:</b> Please go to "MQTT and Network Configuration" and select
+"Wifi only" as the network device (unless you use other network hardware).
 
 ## Installation
 
@@ -176,14 +179,27 @@ For example, to add a code:
 
 ## GPIO lock control (optional)
 
-The lock can be controlled via GPIO. For security reasons, this has to be enabled in
+The lock can be controlled via GPIO. To enable GPIO control, go the the "GPIO Configuration" page where each GPIO
-the configuration portal (check "Enable control via GPIO" in the NUKI configuration
+can be configured for a specific role:
-section). The Pins use pullup configuration, so they have to be connected to ground to
+
-trigger the action.<br><br>
+- Disabled: The GPIO is disabled
-The Pin configuration is:<br>
+- Input: Lock: When connect to Ground, a lock command is sent to the lock
-32: Lock<br>
+- Input: Unlock: When connect to Ground, an unlock command is sent to the lock
-33: Unlock<br>
+- Input: Unlatch: When connect to Ground, an unlatch command is sent to the lock 
-27: Unlatch
+- Input: Electric strike actuation: When connect to Ground, an electric strike actuation command is sent to the opener (open door for configured amount of time)
+- Input: Activate RTO: When connect to Ground, Ring-to-open is activated (opener)
+- Input: Activate CM: When connect to Ground, Continuous mode is activated (opener)
+- Input: Deactivate RTO/CM: Disable RTO or CM, depending on which is active
+- Output: High when locked: Outputs a high signal when the door is locked
+- Output: High when unlocked: Outputs a high signal when the door is unlocked
+- Output: High when motor blocked: Outputs a high signal when the motor is blocked (lock)
+- Output: High when RTO active: Outputs a high signal when ring-to-open is active (opener)
+- Output: High when CM active: Outputs a high signal when continuous mode is active (opener)
+- Output: High when RTO or CM active: Outputs a high signal when either ring-to-open or continuous mode is active (opener)
+
+Note: The old setting "Enable control via GPIO" is removed. If you had enabled this setting before upgrading to 8.22, the PINs are automatically configured to be
+compatible with the previously hard-coded PINs.
+
 
 ## Connecting via LAN (Optional)
 

main.cpp

@@ -1,5 +1,4 @@
 #include "Arduino.h"
-#include "Pins.h"
 #include "NukiWrapper.h"
 #include "NetworkLock.h"
 #include "WebCfgServer.h"

networkDevices/W5500Device.cpp

@@ -1,7 +1,6 @@
 #include <Arduino.h>
 #include <WiFi.h>
 #include "W5500Device.h"
-#include "../Pins.h"
 #include "../PreferencesKeys.h"
 #include "../Logger.h"
 #include "../MqttTopics.h"